《機械專業外文翻譯--在高速潮濕機械加工條件下后刀面表層磨損機理》由會員分享，可在線閱讀，更多相關《機械專業外文翻譯--在高速潮濕機械加工條件下后刀面表層磨損機理（45頁珍藏版）》請?jiān)谘b配圖網上搜索。
1、19CHAPTER VTOOL WEAR MECHANISMS ON THE FLANK SURFACE OF CUTTING INSERTSFOR HIGH SPEED WET MACHINING5.1 IntroductionAlmost every type of machining such as turning, milling, drilling, grinding., uses a cutting fluid to assist in the cost effective production of parts as set up standard required by the
2、 producer 1. Using coolant with some cutting tools material causes severe failure due to the lack of their resistance to thermal shock (like AL2O3 ceramics), used to turn steel. Other cutting tools materials like cubic boron nitride (CBN) can be used without coolant, due to the type of their functio
3、n. The aim of using CBN is to raise the temperature of the workpice to high so it locally softens and can be easily machined. The reasons behind using cutting fluids can be summarized as follows. Extending the cutting tool life achieved by reducing heat generated and as a result less wear rate is ac
4、hieved. It will also eliminate the heat from the shear zone and the formed chips. Cooling the work piece of high quality material under operation plays an important role since thermal distortion of the surface and subsurface damage is a result of excessive heat that must be eliminated or largely red
5、uced to produce a high quality product.Reducing cutting forces by its lubricating effect at the contact interface region and washing and cleaning the cutting region during machining from small chips. The two main reasons for using cutting fluids are cooling and lubrication.Cutting Fluid as a Coolant
6、:The fluid characteristics and condition of use determine the coolant action of the cutting fluid, which improves the heat transfer at the shear zone between the cutting edge, work piece, and cutting fluid. The properties of the coolant in this case must include a high heat capacity to carry away he
7、at and good thermal conductivity to absorb the heat from the cutting region. The water-based coolant emulsion with its excellent high heat capacity is able to reduce tool wear 44.Cutting Fluid as a Lubricant:The purpose is to reduce friction between the cutting edge, rake face and the work piece mat
8、erial or reducing the cutting forces (tangential component). As the friction drops the heat generated isdropped. As a result, the cutting tool wear rate is reduced and the surface finish is improved.Cutting Fluid PropertiesFree of perceivable odorPreserve clarity throughout lifeKind and unirritated
9、to skin and eyes.Corrosion protection to the machine parts and work piece.Cost effective in terms off tool life, safety, dilution ratio, and fluid life. 15.1.1 Cutting Fluid TypesThere are two major categories of cutting fluidsNeat Cutting OilsNeat cutting oils are poor in their coolant characterist
10、ics but have an excellent lubricity. They are applied by flooding the work area by a pump and re-circulated through a filter, tank and nozzles. This type is not diluted by water, and may contain lubricity and extreme-pressure additives to enhance their cutting performance properties. The usage of th
11、is type has been declining for their poor cooling ability, causing fire risk, proven to cause health and safety risk to the operator 1. Water Based or Water Soluble Cutting FluidsThis group is subdivided into three categories:1. Emulsion mineral soluble white-milky color as a result of emulsion of o
12、il in water. Contain from 40%-80% mineral oil and an emulsifying agent beside corrosion inhibitors, beside biocide to inhibit the bacteria growth.2. Micro emulsion semi-synthetic invented in 1980s, has less oil concentration and/or higher emulsifier ratio 10%-40% oil. Due to the high levels of emuls
13、ifier the oil droplet size in the fluid are smaller which make the fluid more translucent and easy to see the work piece during operation. Other important benefit is in its ability to emulsify any leakage of oil from the machine parts in the cutting fluid, a corrosion inhibitors, and bacteria contro
14、l.3. Mineral oil free synthetic is a mix of chemicals, water, bacteria control, corrosion inhibitors, and dyes. Does not contain any mineral oils, and provides good visibility.23 to the work piece. bare in mind that the lack of mineral oil in this type of cuttingfluid needs to take more attention to
15、 machine parts lubrication since it should not leave an oily film on the machine parts, and might cause seals degradation due the lack of protection.5.1.2 Cutting Fluid SelectionMany factors influence the selection of cutting fluid; mainly work piece material, type of machining operation, machine to
16、ol parts, paints, and seals. Table 5-1 prepared at the machine tool industry research association 2 provides suggestions on the type of fluid to be used.5.1.3 Coolant ManagementTo achieve a high level of cutting fluids performance and cost effectiveness, a coolant recycling system should be installe
17、d in the factory. This system will reduce the amount of new purchased coolant concentrate and coolant disposable, which will reduce manufacturing cost. It either done by the company itself or be rented out, depends on the budget and management policy of the company 1. Table 5-1 Guide to the selectio
18、n of cutting fluids for general workshop applications.MachiningoperationWorkpiece materialFree machiningand low -carbon steelsMedium-Carbon steelsHigh Carbonand alloy steelsStainless andheat treatedresistantalloysGrindingClear type soluble oil, semi synthetic or chemical grinding fluidTurningGeneral
19、 purpose, soluble oil, semisynthetic or synthetic fluidExtreme-pressure soluble oil,semi-synthetic or syntheticfluidMillingGeneralpurpose,soluble oil,semi syntheticor syntheticfluidExtreme-pressure solubleoil, semi-synthetic orsynthetic fluidExtreme-pressure soluble oil,semi-synthetic or syntheticfl
20、uid(neat cutting oils may benecessary)DrillingExtremepressure solubleoil, semisynthetic orsynthetic fluidGear ShappingExtreme-pressure soluble oil,semi-synthetic or synthetic fluidNeat-cutting oils preferableHobbingExtreme-pressure soluble oil, semi-synthetic orsynthetic fluid (neat cutting oils may
21、 be preferable)Neat-cuttingoilspreferableBratchingExtreme-pressure soluble oil, semi-synthetic or synthetic fluid (neatcutting oils may be preferable)TappingExtreme-pressure soluble oil, semi-synthetic orsynthetic fluid(neat cutting oils may be necessary)Neat-cuttingoilspreferableNote: some entreis
22、deliberately extend over two or more columns, indicating a wide range of possible applications. Other entries are confined to a specific class of work material.Adopted from Edward and Wright 25.2 Wear Mechanisms Under Wet High Speed MachiningIt is a common belief that coolant usage in metal cutting
23、reduces cutting temperature and extends tools life. However, this research showed that this is not necessarily true to be generalized over cutting inserts materials. Similar research was carried out on different cutting inserts materials and cutting conditions supporting our results. Gu et al 36 hav
24、e recorded a difference in tool wear mechanisms between dry and wet cutting of C5 milling inserts. Tonshoff et al 44 also exhibited different wear mechanisms on AL2O3/TiC inserts in machining ASTM 5115, when using coolants emulsions compared to dry cutting. In addition, Avila and Abrao 20 experience
25、d difference in wear mechanisms activated at the flank side, when using different coolants in testing AL2O3lTiC tools in machining AISI4340 steel. The wear mechanisms and the behavior of the cutting inserts studied in this research under wet high speed-machining (WHSM) condition is not fully underst
26、ood. Therefore, it was the attempt of this research to focus on the contributions in coating development and coating techniques of newly developed materials in order to upgrade their performance at tough machining conditions. This valuable research provides insight into production timesavings and in
27、crease in profitability. Cost reductions are essential in the competitive global economy; thus protecting local markets and consisting in the search of new ones.5.3 Experimental Observations on Wear Mechanisms of Un-Coated Cemented Carbide Cutting Inserts in High Speed Wet MachiningIn this section,
28、the observed wear mechanisms are presented of uncoated cemented carbide tool (KC313) in machining ASTM 4140 steel under wet condition. The overall performance of cemented carbide under using emulsion coolant has been improved in terms of extending tool life and reducing machining cost. Different typ
29、es of wear mechanisms were activated at flank side of cutting inserts as a result of using coolant emulsion during machining processes. This was due to the effect of coolant in reducing the average temperature of the cutting tool edge and shear zone during machining. As a result abrasive wear was re
30、duced leading longer tool life. The materials of cutting tools behave differently to coolant because of their varied resistance to thermal shock. The following observations recorded the behavior of cemented carbide during high speed machining under wet cutting.Figure 5-1 shows the flank side of cutt
31、ing inserts used at a cutting speed of 180m/min. The SEM images were recorded after 7 minutes of machining. It shows micro-abrasion wear, which identified by the narrow grooves along the flank side in the direction of metal flow, supported with similar observations documented by Barnes and Pashby 41
32、 in testing through-coolant-drilling inserts of aluminum/SiC metal matrix composite. Since the cutting edge is the weakest part of the cutting insert geometry, edge fracture started first due to the early non-smooth engagement between the tool and the work piece material. Also, this is due to stress
33、 concentrations that might lead to a cohesive failure on the transient filleted flank cutting wedge region 51, 52. The same image of micro-adhesion wear can be seen at the side and tool indicated by the half cone27 shape on the side of cutting tool. To investigate further, a zoom in view was taken a
34、tthe flank side with a magnification of 1000 times and presented in Figure 5-2A. It shows clear micro-abrasion wear aligned in the direction of metal flow, where the cobalt binder was worn first in a higher wear rate than WC grains which protruded as big spherical droplets. Figure 5-2B provides a zo
35、om-in view that was taken at another location for the same flank side. Thermal pitting revealed by black spots in different depths and micro-cracks, propagated in multi directions as a result of using coolant. Therefore, theiiial pitting, micro-adhesion and low levels of micro-abrasion activated und
36、er wet cutting; while high levels of micro-abrasion wear is activated under dry cutting (as presented in the previous Chapter).Figure 5-3A was taken for a cutting insert machined at 150mlmin. It shows a typical micro-adhesion wear, where quantities of chip metal were adhered at the flank side tempor
37、arily. Kopac 53 exhibited similar finding when testing HSS-TiN drill inserts in drilling SAE1045 steel. This adhered metal would later be plucked away taking grains of WC and binder from cutting inserts material and the process continues. In order to explore other types of wear that might exist, a z
38、oom-in view with magnification of 750 times was taken as shown in Figure5-3B. Figure 5-3B show two forms of wears; firstly, micro-thermal cracks indicated by perpendicular cracks located at the right side of the picture, and supported with similar findings of Deamley and Trent 27. Secondly, micro-ab
39、rasion wear at the left side of the image where the WC grains are to be plucked away after the cobalt binder was severely destroyed by micro-abrasion. Cobalt binders are small grains and WC is the big size grains. The severe distortion of the binder along with the WC grains might be due to the activ
40、ation of micro-adhesion and micro-abrasionFigure 5-1 SEM image of (KC313) showing micro abrasion and micro-adhesion (wet). SEM micrographs of (KC313) at 180m/min showing micro-abrasion where cobalt binder was worn first leaving protruded WC spherical droplets (wet).(a) SEM micrographs of (KC313) at
41、180m/min showing thermal pitting (wet).Figure 5-2 Magnified views of (KC313) under wet cutting: (a) SEM micrographs of (KC313) at 180mlmin showing micro-abrasion where cobalt binder was worn first leaving protruded WC spherical droplets (wet ), (b) SEM micrographs of (KC313) at 180.m/min showing the
42、rmal pitting (wet ). SEM image showing micro-adhesion wear mechanism under 150m/min (wet).(a) SEM image showing micro-thermal cracks, and micro-abrasion.Figure 5-3 Magnified views of (KC313) at 150m/min (wet): (a) SEM image showing micro-adhesion wear mechanism under 150m/min (wet), (b) SEM image sh
43、owing micro-fatigue cracks, and micro-abrasion (wet).Wear at the time of cutting conditions of speed and coolant introduction. Therefore, micro-fatigue, micro-abrasion, and micro-adhesion wear mechanisms are activated under wet condition, while high levels of micro-abrasion were observed under dry o
44、ne.Next, Figure 5-4A was taken at the next lower speed (120m/min). It shows build up edge (BUE) that has sustained its existence throughout the life of the cutting tool, similar to Huang 13, Gu et al 36 and Venkatsh et al 55. This BUE has protected the tool edge and extended its life. Under dry cutt
45、ing BUE has appeared at lower speeds (90 and 60 m/min), but when introducing coolant BUE started to develop at higher speeds, This is due to the drop in shear zone temperature that affected the chip metal flow over the cutting tool edge, by reducing the ductility to a level higher than the one exist
46、ing at dry condition cutting. As a result, chip metal starts accumulating easier at the interface between metal chip flow, cutting tool edge and crater surface to form a BUE. In addition to BUE formation, micro-abrasion wear was activated at this speed indicated by narrow grooves.To explore the poss
47、ibility of other wear mechanisms a zoom-in view with a magnification of 3500 times was taken and shown in Figure 5-4B. Micro- fatigue is evident by propagated cracks in the image similar to Deamley and Trent 27 finding. Furthermore, Figure 5-4B shows indications of micro-abrasion wear, revealed by t
48、he abrasion of cobalt binder and the remains of big protruded WC grains. However, the micro-abrasion appeared at this speed of 120m/min is less severe than the same type of micro-wear observed at 150 m/min speed, supported with Barnes 41 similar findings. Therefore, micro-abrasion, BUE and micro-fat
49、igue were activated under wet condition while, adhesion, high levels micro-abrasion, and no BUE were under dry cutting. SEM image of (KC313) showing build up edge under 120m/min (wet).(a) SEM image of (KC3 13) showing micro-fatigue, and micro-abrasion (wet).Figure 5-4 SEM images of (KC313) at 120m/m
50、in (wet), (a) SEM image of (KC313). showing build up edge, (b) SEM image of (KC313) showing micro-fatigue and micro-abrasion33 Figure 5-5 is for a cutting tool machined at 90m/min, that presents a goodcapture of one stage of tool life after the BUE has been plucked away. The bottom part of the flank
51、 side shows massive metal adhesion from the work piece material. The upper part of the figure at the edge shows edge fracture. To stand over the reason of edge fracture, the zoom-in view with magnification of 2000 times is presented in Figure 5-6A. The micro-fatigue crack image can be seen as well a
52、s micro-attrition revealed by numerous holes, and supported with Lim et al 31 observations on HSS-TiN inserts. As a result of BUE fracture from the cutting tool edge, small quantities from the cutting tool material is plucked away leaving behind numerous holes. Figure 5-6B is another zoom-in view of
53、 the upper part of flank side with a magnification of 1000 times and shows micro-abrasion wear indicated by the narrow grooves. Furthermore, the exact type of micro-wear mechanism appeared at the flank side under 60 m/min. Therefore, in comparison with dry cutting at the cutting speed of 90 m/min an
54、d 60 m/min, less micro-abrasion, bigger BUE formation, and higher micro-attrition rate were activated. Figure 5-5 SEM image showing tool edge after buildup edge was plucked away. SEM image showing micro-fatigue crack, and micro-attrition.(a) SEM image showing micro-abrasion.Figure 5-6 SEM images of
55、(KC313) at 90m/min:(a) SEM image showing micro-fatigue crack, and micro-attrition, (b) SEM image showing micro-abrasion.5.4 Experimental Observations on Wear Mechanisms of Coated Cemented Carbide with TiN-TiCN-TiN Coating in High Speed Wet MachiningInvestigating the wear mechanisms of sandwich coati
56、ng under wet cutting is presented in this section starting from early stages of wear. Figure 5-7 shows early tool wear starting at the cutting edge when cutting at 410m/min. Edge fracture can be seen, it has started at cutting edge due to non-smooth contact between tool, work piece, micro-abrasion a
57、nd stress concentrations. To investigate further the other possible reasons behind edge fracture that leads to coating spalling, a zoom-in view with magnification of 2000 times was taken and presented at Figure 5-8A. Coating fracture can be seen where fragments of TiN (upper coating) had been plucke
58、d away by metal chips. This took place as result of micro-abrasion that led to coating spalling. On the other hand, the edge is the weakest part of the cutting insert geometry and works as a stress concentrator might lead to a cohesive failure on the transient filleted flank cutting wedge region 51,
59、 52.Both abrasion wear and stress concentration factor leave a non-uniform edge configuration at the micro scale after machining starts. Later small metal fragments started to adhere at the developed gaps to be later plucked away by the continuous chip movement as shown in Figure 5-8A. Another view
60、of edge fracture was taken of the same cutting tool with a magnification of 2000 times as shown in Figure 5-8B. It presents fracture and crack at the honed tool edge. A schematic figure indicated by Figure 5-9, presented the progressive coated cutting inserts failure starting at the insert edge. It
61、was also noticed during the inserts test that failure takes place first at the inserts edge then progressed toward the flank side. Consequently, a study on optimizing the cutting edgeFigure 5-7 SEM image of (KC732) at 410m/min showing edge fracture and micro-abrasion (wet). SEM image showing edge fr
62、acture.(a) SEM image showing fracture and crack at the honed insert edge.Figure 5-8 SEM of (KC732) at 410m/min and early wear stage (wet): (a) SEM image showing edge fracture, (b) SEM image showing fracture and crack at the honed insert edge. radius to improve coating adhesion, and its wear resistan
63、ce, might be also a topic for future work.Figure 5-1.0A was taken after tool failure at a speed of 410m/min. It shows completely exposed substrate and severe sliding wear at the flank side. The coating exists at the crater surface and faces less wear than the flank side. Therefore it works as an upp
64、er protector for the cutting edge and most of the wear will take place at the flank side as sliding wear. Figure 5-10B is a zoom-in view with magnification of 3500 times, and shows coating remaining at the flank side. Nonetheless, micro-abrasion and a slight tensile fracture in the direction of meta
65、l chip flow. Ezugwa et al 28 and Kato 32 have exhibited similar finding. However, the tensile fracture in this case is less in severity than what had been observed at dry cutting. This is due to the contribution of coolant in dropping the cutting temperature, which has reduced the plastic deformation at high temperature as a result. Hence, in comparison with the dry cutting at the same speed, tensile fracture was available w
機械專業外文翻譯--在高速潮濕機械加工條件下后刀面表層磨損機理
